Use as a Horizontal screw centrifuge I am well aware of the importance of improving work efficiency and ensuring stable operation of equipment. This article will introduce the horizontal snail in detail Centrifuge And share some operation adjustment skills to help readers better master the use of horizontal spiral centrifuge.

I Operation method of horizontal screw centrifuge

1. Preparation:

Before operating the horizontal screw centrifuge, ensure that the equipment is in good working condition. Clean the workbench and check whether the centrifuge is worn or damaged abnormally. At the same time, ensure the safety equipment is intact, such as safety isolation cover, maintenance button, etc.

2. Sample preparation: Put the sample to be centrifuged into the centrifuge rotor. According to the characteristics of the sample and the specifications of the centrifuge, select the appropriate centrifuge tube or centrifuge box, and ensure that the sample is evenly distributed in the rotor to avoid the centrifuge vibration caused by unbalanced loading.

3. Parameter setting: Set relevant parameters according to the required centrifugal force and time. These parameters will directly affect the quality and results of centrifugal operation. Centrifugal force is usually expressed in "× g" (relative centrifugal acceleration), and centrifugal time is expressed in minutes. Ensure that the set parameters meet the requirements of centrifuge and sample.

4. Start the centrifuge: After confirming that all parameters are set correctly, close the safety isolation cover and press the start button. The centrifuge will start to rotate and generate centrifugal force to settle or separate the sample. During operation, closely observe the working state of the centrifuge to ensure its normal operation.

5. Stop the centrifuge: After the centrifuge time reaches the set value, press the stop button to let the centrifuge gradually slow down and stop, and wait for the centrifuge to completely stop before opening the safety isolation cover. Be careful not to open the safety isolation cover too early to avoid accidental injury.

2、 Operation and adjustment skills of horizontal screw centrifuge

1. Balance adjustment: The key to avoid vibration and noise is to ensure that the sample is loaded evenly in the rotor of the centrifuge. If the centrifuge has obvious vibration or noise during operation, it is necessary to check the loading balance of the sample and readjust the sample position to make it evenly distributed.

2. Speed adjustment: The rotating speed (rpm) of the centrifuge is an important parameter that needs to be adjusted during operation. Select the appropriate speed according to the requirements of the sample and the specifications of the centrifuge. Too high rotating speed may lead to incomplete sample separation, while too low rotating speed may affect the centrifugal effect. Adjust the rotating speed timely to obtain the best centrifugal result.

3. Temperature control: Some samples are sensitive to temperature during centrifugation. During operation, try to control the ambient temperature of the centrifuge and ensure that the sample is centrifuged within the allowable temperature range. It should be noted that the high-speed operation of the centrifuge will also generate some heat, so after the centrifugation, a period of time should be set aside for the sample to cool.

Conclusion:

Mastering the operation method and operation adjustment skills of horizontal screw centrifuge is very important for the correct use of horizontal screw centrifuge and obtaining satisfactory results. I hope that the above contents can provide readers with some references and guidance on horizontal spiral centrifuges, and improve work efficiency and sample separation quality.

Note: The Manufacturer of horizontal spiral centrifuge Specific manufacturers can be selected for purchase according to actual needs.

Zhejiang Zhengda Environmental Protection Equipment Co., Ltd.: focusing on Horizontal spiral sedimentation centrifuge, sludge dewatering machine, sludge treatment equipment, centrifugal dewatering machine, sludge dewatering equipment, solid-liquid separation equipment, horizontal spiral centrifuge, centrifuge, mud dewatering machine, mud dewatering equipment, mud treatment equipment, horizontal centrifuge, solid-liquid separator Production, sales and service of various solid-liquid separation equipment. Welcome new and old customers to come for consultation and investigation.

Factory address: No. 812, Jiulong Street, Bihu Town Industrial Zone, Liandu District, Lishui City, Zhejiang Province Telephone: 0578-2788008     Fax ：0578-2788681
  Email: [email protected]      website: //hcsxe.com
Mobile: 15857812218 (Mr. Mao)    fifteen billion two hundred and fifty-seven million eight hundred and twenty-six thousand six hundred and nine (Manager Xu) thirteen billion nine hundred and six million seven hundred and eighty-eight thousand three hundred and sixty-seven (Mr. Xu)